Failure load prediction of single-lap bonded joints by damage zone method

195 views

Authors

  • Truong Viet Hoai (Corresponding Author) Faculty of Mechanical Engineering, Le Quy Don Technical University
  • Tran Duc Hoan Faculty of Mechanical Engineering, Le Quy Don Technical University
  • Vu Minh Vinh Faculty of Mechanical Engineering, Le Quy Don Technical University
  • Chu Van Huy Faculty of Mechanical Engineering, Le Quy Don Technical University

DOI:

https://doi.org/10.54939/1859-1043.j.mst.79.2022.52-59

Keywords:

Single-lap joint; Composite; Damage zone method; Finite element analysis; Failure load prediction.

Abstract

The failure load of single-lap bonded joints with dissimilar adherend materials was predicted using the damage zone method. A number of six joint configurations with different thicknesses of the adherends were considered. Three-dimensional finite element models were built to represent the behavior of the bonded joints, and the damage zone method was applied to predict the failure loads of the joints. The predictions of failure loads of the joints were achieved, showing a good agreement between the numerical and the corresponding experimental results.

References

[1]. “An Introduction to Composite Materials”, Cambridge University Press, Cambridge; 1981.

[2]. Da Silva LFM, O¨ chsner A. “Modeling of adhesive bonded joints”. Berlin: Springer; 2008.

[3]. Harris, J.A. and Adams, R.D. (1984). “Strength Prediction of Bonded Single-lap Joints by Nonlinear Finite Element Methods”, International Journal of Adhesion & Adhesives, 4(2): 65-78.

[4]. Crocombe, A.D. (1989). “Global Yielding as a Failure Criterion for Bonded Joints”, International Journal of Adhesion & Adhesives, 9(3): 145-153.

[5]. Mazumdar SK, Mallick PK. “Static and fatigue behavior of adhesive joints in SMC–SMC composites”. Polymer Compos 1998;19(2):139–46.

[6]. Li G, Lee-Sullivan P, Thring RW. “Nonlinear finite element analysis of stress and strain distributions across the adhesive thickness in composite single-lap joints”. Compos Struct 1999; 46:395–403.

[7]. Kairouz KC, Matthews FL. “Strength and failure modes of bonded single-lap joints between cross-ply adherends”. Composites 1993;24(6):475–84.

[8]. Kim KS, Yoo JS, Yi YM, Kim CG. “Failure mode and strength of uni-directional composite single-lap bonded joints with different bonding methods”. Compos Struct 2006; 72:477–85.

[9]. Shin, K.C. and Lee, J.J. (2000). “Prediction of the Tensile Load-bearing Capacity of a Co-cured Single-lap Joint Considering Residual Thermal Stresses”, Journal of Adhesion Science and Technology, 14(13): 1691-1704

[10]. Owens JFP, Lee-Sullivan P. “Stiffness behavior due to fracture in adhesively bonded composite-to-aluminum joints I. Theoretical model”. Int J Adhes Adhes 2000; 20:39–45.

[11]. Owens JFP, Lee-Sullivan P. “Stiffness behavior due to fracture in adhesively bonded composite-to-aluminum joints II. Experimental”. Int J Adhes Adhes 2000; 20:47–58.

[12]. Seong MS, Kim TH, Nguyen KH, Kweon JH, Choi JH. “A parametric study on the failure of bonded single-lap joints of carbon composite and aluminium”. Compos Struct 2008; 86:135–45.

[13]. Nguyen KH, Kweon JH, Choi JH. “Failure load prediction by damage zone method for single lap bonded joints of carbon composite and aluminum”. J. Compos. Mater. 2009;43: 3031–3056.

[14]. Park YB, Song MG, Kim JJ, et al. “Strength of carbon/epoxy composite single-lap bonded joints in various environmental conditions”. Compos Struct. 2010; 92:2173–2180.

[15]. Song MG, Kweon JH, Choi JH, Byun JH, Song MH. “Effect of manufacturing methods on the shear strength of composite single-lap bonded joints”. Compos Struct 2010; 92:2194–2202.

[16]. Sheppard, A., Tong, L. and Kelly, D. (1998). “A Damage Zone Model for the Failure Analysis of Adhesively Bonded Joints”, International Journal of Adhesion & Adhesives, 18(6): 385-400.

[17]. Truong, V. et al. “Failure load prediction of laminates repaired with a scarf-bonded patch using the damage zone method”. Adv Compos Mater 26(2), 115-133, 2017.

[18]. Ban CS, Lee YH, Choi JH, Kweon JH. “Strength prediction of adhesive joints using the modified damage zone theory”. Compos Struct 2008; 86:96–100.

[19]. Li F et al. “Deformation and failure of hybrid composite sandwich beams with a metal foam core under quasi-static load and low-velocity impact”. Engineering Failure Analysis 2020;118.

[20]. Dharmavarapu P et al. “Failure Analysis of Silane-Treated Kevlar-Reinforced Nano-silica-Toughened Epoxy Composite in Laminar Shear Strength, Drop Load Impact and Drilling Process”. Journal of Failure Analysis and Prevention 2020.

Downloads

Published

19-05-2022

How to Cite

Truong Viet, H., Tran Duc Hoan, Vu Minh Vinh, and Chu Van Huy. “Failure Load Prediction of Single-Lap Bonded Joints by Damage Zone Method”. Journal of Military Science and Technology, no. 79, May 2022, pp. 52-59, doi:10.54939/1859-1043.j.mst.79.2022.52-59.

Issue

Section

Research Articles