Research on manufacturing energy-carrying materials from nitrocellulose, cellulose and unsaturated polyester

130 views

Authors

  • Pham Van Khuong (Corresponding Author) Institute of Chemistry and Materials, Academy of Military Science and Technology
  • Do Duc Tri Institute of Propellant and Explosives
  • Nguyen Manh Tuong Institute of Chemistry and Materials, Academy of Military Science and Technology
  • Hoang The Vu Institute of Propellant and Explosives

DOI:

https://doi.org/10.54939/1859-1043.j.mst.IPE.2024.68-73

Keywords:

Polyethylene glycol maleate phthalate; Mechanical properties; Heat of combustion; Flash point.

Abstract

This article presents the results of research and fabrication of energy-carrying composite materials from nitrocellulose (NC), cellulose (C) and unsaturated polyester. The results show that the material sample has satisfactory properties when the ratio nitrocellulose:cellulose (NC:C)-80:20 and the content of unsaturated polyester is 15%, the material has tensile strength is not less than 10 MPa (11.56 MPa), elongation is not less than 1.5% (4.2%), heat of combustion is not less than 500 kcal/g (513.6 kcal/g), flash temperature is not less than 180 oC (193 oC).

References

[1]. F.W. Robbin, J.W. Colburn. “Combustible cartridge case: Curent status and future prospects”, Technial report, Ballistic research laboratory Aberdeen Proving Ground, Maryland (1992).

[2]. G. R. Kurulkar, R. K. Syal & Haridwar Singh. “Combustible cartridge case formulation and evaluation”, Journal of Energetic Materials, 14:2, 127-149, (1996), DOI: 10.1080/07370659608216061.

[3]. Yang W-t, Yang J-x, Zhang Y-c, Ying S-j. “A coMParative study of combustible cartridge case materials”. Defence Technology, (2017), doi: 10.1016/j.dt.2017.02.003.

[4]. А.Н. Крестовский, “Разработка олигоэфируретанакрилатного сгораемого материала и технологии изготовления нового поколения жестких сгораемых картузов для модульных метательных зарядов”. ФГУП «Научно-исследовательский институт полимерных материалов». Пермь. (2011).

[5]. Peter L. DeLuca, “Cartridge case and method for the manufacture thereof”. Patent US3320886.

[6]. Гарбар М.И., Акутин М.С., Егорова Н.М. (ред.). Справочник по пластическим массам.

[7]. Abhijit Dey, Javaid Athar. “Improvements in the Structural Integrity of Resin Based Combustible Cartridge Cases (CCC) at Elevated Temperatures”. Central European Journal of Energetic Materials, 12(1), 117-127. ISSN 2353-1843. (2015).

[8]. Nguyen Van Hung, Tran Huu Thanh, Pham Van Khuong, Doan Van Diep, Nguyen Duc Long. “Research and development of a fireproof coating under low-temperature conditions for ballistite fuel for a main rocket engine”. Journal of Science and Technology 03B, pp. 34-38, (2023).

Published

14-10-2024

How to Cite

Phạm Văn Khương, Đỗ Đức Trí, Nguyễn Mạnh Tường, and Hoàng Thế Vũ. “Research on Manufacturing Energy-Carrying Materials from Nitrocellulose, Cellulose and Unsaturated Polyester”. Journal of Military Science and Technology, no. IPE, Oct. 2024, pp. 68-73, doi:10.54939/1859-1043.j.mst.IPE.2024.68-73.

Issue

Section

Research Articles

Categories

Most read articles by the same author(s)